![]() ![]() NOTE: Some Panic/Hold-Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center. If your system is connected to a monitoring center, an emergency report could be transmitted to that center. Police (Panic/Hold-Up) Key: This key can sound a local audible alarm when pressed for two seconds. If your system is connected to a monitoring center, an emergency report could be sent to that center. If your system is connected to a monitoring center, an emergency report could be sent to that centerĪuxiliary Emergency Key: This key can activate the auxiliary alarm when pressed for two seconds. If your system is programmed for these functions, the following reports can be sent.įire Key: This key can activate the fire alarm when pressed for two seconds. You should press these keys only in an emergency situation that requires response by emergency personnel. Your system may not be programmed for these activation keys (see page 1). NOTE: You must hold these keys for 2 seconds to activate these functions. Once armed (and the bypass toggle feature is enabled) press the key again to exit group bypassing. Now you can arm your system in either the or mode. ![]() NOTE: All zones will automatically be un-bypassed each time the system is disarmed.īy pressing the key, followed by the key, then the key again, all zones that are designated as group bypass zones will be bypassed. The corresponding light for that zone will go off when un-bypassed. To manually un-bypass zones, perform the bypassing procedure on a zone that is already bypassed. The Bypass light will stop flashing upon exiting the Bypass Mode. Step 7 Press the key again or press the key to exit the Bypass Mode. Repeat 4 for any other zone(s) that need to be bypassed. Step 6 The corresponding zone light will illuminate indicating the zone has been bypassed. (Example: Press the – key for zone 1, press – for zone 12.) Step 4 Enter a 2 digit zone indicating the zone you wish to bypass. The following steps are used for bypassing zones: If you wish to bypass one or more zones, this must be done while the system is in the disarmed state. Networx nx 8 how to reset smoke detector code#If a valid code is not entered before the end of the entry delay, an alarm will occur. After entering a valid code the red armed light will go off and the tone will stop. When you enter the protected area through one of the designated Entry/Exit doors, the code pad control will sound a solid continuous tone for the duration of the entry delay time, or until you enter a valid user code. This is ideal for a maid or baby sitter code, etc. This feature is used for ARMING ONLY, and should not be enabled to disarm the security system. The system can be quick armed in the PARTIAL mode by pressing the key. Quick Arm will allow the user to arm the security system in the ON mode by pressing the key. The Quick Arm feature may be used if it is enabled. USING THE QUICK ARM: (Optional, if programmed) The light(s) corresponding to the bypassed zone(s) will illuminate, alerting the user that a zone(s) may be unprotected and can be faulted without an alarm. The bypass light will illuminate if any zone(s) is bypassed. If the power light is off, you have no AC power. The security system will not arm if the ready light is not on or flashing. NOTE: If any zones are bypassed, a sensor in that zone can be violated without affecting the ready light. Ready light must be on or flashing when all protected zones and sensors are secure. Listed below are the steps to arm in the PARTIAL Mode: PARTIAL is used when the user is inside the premise and wants protection around the perimeter. ![]() ![]() The user may wish to press the key to start the exit delay again or disarm and rearm the system if more time is needed. NOTE: The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire. The armed and exit lights will illuminate. Step 2 Enter your 4 or 6 digit user code to arm the system. Ready light will be on or flashing when all protected zones and sensors are secure. Step 1 Close all protected doors and windows. Listed below are the steps to arm in the ON Mode: ON is used when the user is away from the premise and wants the interior protected. ![]()
0 Comments
![]() The National Law Review - National Law Forum LLC 3 Grant Square #141 Hinsdale, IL 60521 Telephone (708) 357-3317 or toll free (877) 357-3317. Wordrake blog professional#Unless otherwise noted, attorneys are not certified by the Texas Board of Legal Specialization, nor can NLR attest to the accuracy of any notation of Legal Specialization or other Professional Credentials. Statement in compliance with Texas Rules of Professional Conduct. Attorney Advertising Notice: Prior results do not guarantee a similar outcome. The choice of a lawyer or other professional is an important decision and should not be based solely upon advertisements. ![]() Wordrake blog full#Under certain state laws the following statements may be required on this website and we have included them in order to be in full compliance with these rules. NLR does not answer legal questions nor will we refer you to an attorney or other professional if you request such information from us. The NLR does not wish, nor does it intend, to solicit the business of anyone or to refer anyone to an attorney or other professional. Some states have laws and ethical rules regarding solicitation and advertisement practices by attorneys and/or other professionals. The National Law Review is not a law firm nor is intended to be a referral service for attorneys and/or other professionals. No attorney-client or confidential relationship is formed by the transmission of information between you and the National Law Review website or any of the law firms, attorneys or other professionals or organizations who include content on the National Law Review website. If you require legal or professional advice, kindly contact an attorney or other suitable professional advisor. Any legal analysis, legislative updates or other content and links should not be construed as legal or professional advice or a substitute for such advice. The National Law Review is a free to use, no-log in database of legal and business articles. The content and links on intended for general information purposes only. You are responsible for reading, understanding and agreeing to the National Law Review's (NLR’s) and the National Law Forum LLC's Terms of Use and Privacy Policy before using the National Law Review website. ![]() ![]() |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |